Subaru 2005 Legacy User Manual

ForewordCongratulations on choosing a SUBARU vehicle. This Owner’s Man-ual has all the information necessary to keep your SUBARU in excel-lent conditi

7– CONTINUED –ment, the driver should always sit upright andwell back in the seat as far from the steeringwheel as practical while still maintaining f

1-69Seat, seatbelt and SRS airbags– CONTINUED –NOTEThe driver’s SRS side airbag, SRS curtain airbagand seatbelt pretensioner are not controlled by the

1-70Seat, seatbelt and SRS airbagsIf your vehicle has sustained impact, this may affectthe proper function of the Subaru advanced frontal air-bag syst

1-71Seat, seatbelt and SRS airbags– CONTINUED –ing the system check, both indicators extinguish for 2seconds. After this, one of the indicators illumi

1-72Seat, seatbelt and SRS airbagsseat, activating the front passenger’s SRS frontal air-bag even though that seat is occupied by a child." Do no

1-73Seat, seatbelt and SRS airbags– CONTINUED –take the following actions." Ensure that no article is placed on the seat otherthan the occupant.&

1-74Seat, seatbelt and SRS airbagsthe side of the seat." Ensure that the backward-forward position andseatback of front passenger’s seat are lock

1-75Seat, seatbelt and SRS airbags– CONTINUED –! OperationA) Driver’s sideB) Passenger’s sideThe SRS airbag can function only when the ignitionswitch

1-76Seat, seatbelt and SRS airbagsfrom detecting impact to the deflation of the SRS air-bag after deployment is shorter than the blink of aneye.Both w

1-77Seat, seatbelt and SRS airbags– CONTINUED –" Examples of accident in which the driver’s/driv-er’s and front passenger’s SRS frontal airbag(s)

1-78Seat, seatbelt and SRS airbagsactivated when the vehicle sustains a hard impact inthe undercarriage area from the road surface (such aswhen the ve

8the lock switch when children are riding in thevehicle. Failure to follow this procedure couldresult in injury to a child operating the powerwindow.

1-79Seat, seatbelt and SRS airbags– CONTINUED –necessarily require deployment of driver’s/driver’s andfront passenger’s SRS frontal airbag(s). If the

1-80Seat, seatbelt and SRS airbagsstruck from side or from behind, or if it rolls onto itsside or roof, or if it is involved in a low-speed frontalcol

1-81Seat, seatbelt and SRS airbags– CONTINUED –do away with the need to fasten seatbelts. It isalso important to wear your seatbelt to helpavoid injur

1-82Seat, seatbelt and SRS airbagsDo not rest your arm on either front door or itsinternal trim. It could be injured in the event ofSRS side airbag de

1-83Seat, seatbelt and SRS airbags– CONTINUED –" Never allow a child to kneel on the front pas-senger’s seat facing the side window or to wraphis

1-84Seat, seatbelt and SRS airbagssory in such a location could be propelledthrough the cabin with great force by the cur-tain airbag, or it could pre

1-85Seat, seatbelt and SRS airbags– CONTINUED –! OperationA) SRS curtain airbags operationB) SRS side airbags operationThe SRS side airbag and SRS cur

1-86Seat, seatbelt and SRS airbagsDo not touch the SRS side airbag system com-ponents around the front seatback with barehands right after deployment.

1-87Seat, seatbelt and SRS airbags– CONTINUED –" Examples of the types of accidents in which the SRS side airbag and SRS curtain airbag are unlik

1-88Seat, seatbelt and SRS airbagsThere are many types of collisions which might notnecessarily require SRS side airbag and SRS curtainairbag deployme

9– CONTINUED –checked and corrected as soon as possible. Ifyou must drive under these conditions, driveonly with all windows fully open." Keep th

1-89Seat, seatbelt and SRS airbags– CONTINUED –B) The vehicle is struck from behind.The SRS side airbag and SRS curtain airbag are basi-cally not desi

1-90Seat, seatbelt and SRS airbagsposition.The following components are monitored by the indi-cator:" Front sub sensor (Right hand side)" Fr

1-91Seat, seatbelt and SRS airbags– CONTINUED –! SRS airbag system servicing" When discarding an airbag module or scrap-ping the entire vehicle d

1-92Seat, seatbelt and SRS airbagsroof side (from the front pillar to a point over therear seat) is scratched, cracked, or otherwise dam-aged." E

1-93Seat, seatbelt and SRS airbags– CONTINUED –placard attached to the driver’s door pillar orspecified for individual vehicle models in thisOwner’s M

2-12Keys and doorsKeys ... 2-2Key number ...

2-2Keys and doorsKeys and doorsKeysVehicle with immobilizer systemA) Master keyB) Submaster keyC) Valet keyD) Key number plateE) Security ID plateVehi

2-3Keys and doors– CONTINUED –The valet key fits only the ignition switch and doorlocks. You can keep the trunk and glove box lockedwhen you leave you

2-4Keys and doorsImmobilizer (if equipped)The immobilizer system is designed to prevent an un-authorized person from starting the engine. Only keysreg

10drugs, please consult with your doctor.Never drive if you are under the influence of any illicitmind-altering drugs. For your own health and well-be

2-5Keys and doors– CONTINUED –! Security ID plateA) Key number plateB) Security ID plateThe security ID is stamped on the metal plate attachedto the k

2-6Keys and doorsNOTEEven if the security indicator light flashes irregu-larly or its fuse blows (the light does not flash if itsfuse is blown), the i

2-7Keys and doors– CONTINUED –Locking without the key1) Rotate the lock lever rearward.2) Close the door.To lock the door from the outside without the

2-8Keys and doorsvehicle before locking the doors from the outsidewithout the key.! Locking and unlocking from the insideKeep all doors locked when yo

2-9Keys and doors– CONTINUED –To unlock the door from the inside, rotate the lock le-ver forward.The red mark on the lock lever appears when the doori

2-10Keys and doorsPower door locking switchesDriver’s switchA) LockB) UnlockFront passenger’s switchA) LockB) UnlockAll doors and the rear gate (Stati

2-11Keys and doors– CONTINUED –the doors remain locked.NOTEMake sure that you do not leave the key inside thevehicle before locking the doors from the

2-12Keys and doorsRemote keyless entry system (if equipped)" Do not expose the transmitter to severeshocks, such as those experienced as a result

2-13Keys and doors– CONTINUED –: Trunk lid/rear gate unlock button: Unlock/disarm button: Lock/arm buttonA: Panic buttona: Frontb: Back! Locking the d

2-14Keys and doors! Unlocking the doorsPress the “ ” button to unlock the driver’s door. Anelectronic chirp will sound twice and the turn signallights

11– CONTINUED –! Driving with petsUnrestrained pets can interfere with your driving anddistract your attention from driving. In a collision orsudden s

2-15Keys and doors– CONTINUED –! Illuminated entryThe interior (dome) light will illuminate when the“ ” button is pressed. This light stays illuminate

2-16Keys and doorssired, you may turn the audible signal off.To turn the audible signal off, unlock the doors bypushing “ ” button and then simultaneo

2-17Keys and doors– CONTINUED –2. Remove the old battery from the holder.A) Negative (–) side facing up3. Replace with a new battery (Type CR2025 oreq

2-18Keys and doorstransmitters (up to four can be programmed), youshould re-program all of your transmitters for securityreasons. It is recommended th

2-19Keys and doors– CONTINUED –3. Perform the following steps within 45 seconds.1)Open and close the driver’s door once.A) LOCKB) ON2)Insert the key i

2-20Keys and doorslamp will not flash. In this event, perform thewhole procedure again beginning with part 1.4. Open and close the door once within 15

2-21Keys and doors– CONTINUED –6. When you have finished entering the number, pullthe lock knob to the “UNLOCK” side within five sec-onds. NOTE"

2-22Keys and doorsNOTEIf the code entered the second time is not identicalto the code entered the first time, an error will oc-cur. In this event, per

2-23Keys and doors– CONTINUED –Alarm systemThe alarm system helps to protect your vehicle andvaluables from theft. The horn sounds and the turnsignal

2-24Keys and doorsTo activate:Repeat moving the door locking switch to the lock po-sition (toward the front) three times. The odometer/tripmeter scree

2-25Keys and doors– CONTINUED –6. Briefly press the “ ” button (for less than two sec-onds). All doors (and the rear gate on the Station wag-on) will

2-26Keys and doors" The alarm system is triggered when the ignitionswitch is turned to the “ON” position during sur-veillance. However, this does

2-27Keys and doors– CONTINUED –! Valet modeWhen you choose the valet mode, the alarm systemdoes not operate. In valet mode, the remote transmit-ter is

2-28Keys and doorsA) ONB) LOCK2. Turn the ignition switch from “ON” to “LOCK” posi-tion and remove the key from the ignition switch.3. Open the doors

2-29Keys and doors– CONTINUED –! Tripped sensor identificationThe security indicator light flashes when the alarmsystem has been triggered. Also, the

2-30Keys and doorsChild safety locksAlways use the child safety lock whenever achild rides in the rear seat. Serious injury couldresult if a child acc

2-31Keys and doors– CONTINUED –Windows! Power windowsTo avoid serious personal injury caused by en-trapment, you must do the following." When ope

2-32Keys and doors" Operating the driver’s windowA) OpenB) Automatically openTo open:Push the switch down lightly and hold it. The windowwill ope

2-33Keys and doors– CONTINUED –" Operating the passengers’ windowsTo open the passengers’ windows, push the appropri-ate switch down and hold it

2-34Keys and doors" Locking the passengers’ windowsTo lock the passengers’ windows, push the lockswitch. When the lock switch is in the “LOCK” po

1491281234567131011Table of contentsSeat, seatbelt and SRS airbagsKeys and doorsInstruments and controlsClimate controlAudioInterior equipmentStarting

2-35Keys and doors– CONTINUED –Rear passengers’ window switchesA) OpenB) CloseTo close the window, pull the switch up and hold it untilthe window reac

2-36Keys and doorsNOTEDo not leave your valuables in the trunk when youleave your vehicle.! To open the trunk lid from insidePull the trunk lid releas

2-37Keys and doors– CONTINUED –! Internal trunk lid release handleThe internal trunk lid release handle is a device de-signed to open the trunk lid fr

2-38Keys and doors! InspectionPerform the following steps at least twice a year tocheck the release handle for correct operation.1. Open the trunk lid

2-39Keys and doors– CONTINUED –3. Move the release handle, from outside the vehicle,in the direction of the arrow to check if the latch is re-leased.I

2-40Keys and doorsTo close the rear gate, lower it slowly and push downfirmly until the latch engages.The rear gate can be lowered easily if you pull

2-41Keys and doors– CONTINUED –Moonroof (if equipped)" Never let anyone’s hands, arms, head or anyobjects protrude from the moonroof. He/shecould

2-42Keys and doors! Tilting/sliding moonroof (Sedan)! Tilt functionA) Tilt upB) Tilt downThe tilting function will only operate when the moon-roof is

2-43Keys and doors– CONTINUED –To stop the moonroof at a selected mid-way positionwhile opening or closing it, momentarily push theswitch to the “OPEN

2-44Keys and doorsThe sun shade can be slid forward or backward byhand while the moonroof is closed.If the moonroof is opened, the sun shade also move

14Illustrated index! Exterior123 5 6413 1112 8910 7UBF200BB1) Engine hood lock release (page 11-5)2) Headlight switch (page 3-45)3) Bulb replacement (

2-45Keys and doors– CONTINUED –approximately 6.7 in (17 cm) from its fully closed posi-tion.After confirming safety, pull the switch to the “OPEN”side

2-46Keys and doorsback.

3-13Instruments and controlsIgnition switch ... 3-3LOCK ...

3-2Instruments and controlsHeadlight indicator light ... 3-35Front fog light indicator light ...

3-3Instruments and controls– CONTINUED –Instruments and controlsIgnition switch" Never turn the ignition switch to “LOCK”while the vehicle is bei

3-4Instruments and controlsholder is attached to the key, your knees or handsmay accidentally touch it in a way that turns the ig-nition switch.! LOCK

3-5Instruments and controls– CONTINUED –! STARTDo not turn the ignition switch to the “START”position while the engine is running.The engine is starte

3-6Instruments and controls" The key is near another key that contains an im-mobilizer transponder.! Key reminder chimeThe reminder chime sounds

3-7Instruments and controls– CONTINUED –Hazard warning flasherThe hazard warning flasher is used to warn other driv-ers when you have to park your veh

3-8Instruments and controls! Canceling the function for meter/gauge needle movement and combina-tion meter sequential illumination upon turning on the

15– CONTINUED –685412375984123UBF201BB1) Rear window defogger button (page 3-57)2) Fuel filler lid and cap (page 7-4)3) Child safety locks (page 2-30)

3-9Instruments and controls– CONTINUED –Briefly press the knob to return to the A trip meter indi-cation.If you turn the ignition switch to the “LOCK”

3-10Instruments and controlsthe “ON” position within 10 seconds of illumination ofthe odometer/trip meter.! Double trip meterThis meter display two tr

3-11Instruments and controls– CONTINUED –NOTEIf the connection between the combination meterand battery is broken for any reason such as vehi-cle main

3-12Instruments and controlsremaining in the tank.When the ignition switch is in the “LOCK” or “ACC” po-sition, the fuel gauge shows “E” even if the f

3-13Instruments and controls– CONTINUED –NOTEYou will see the “ ” sign in the fuel gaugemeter.This indicates that the fuel filler door (lid) is locat-

3-14Instruments and controlsthe engine coolant at this temperature range and highrevving operation when the engine is not warmed upenough should be av

3-15Instruments and controls– CONTINUED –! Canceling the function for meter/gauge needle movement upon turning on the ignition switchIt is possible to

3-16Instruments and controls! OdometerThis meter displays the odometer when the ignitionswitch is in the “LOCK”, “ACC” or “ON” position.The odometer s

3-17Instruments and controls– CONTINUED –To set the trip meter to zero, select the A trip or B tripmeter by pushing the knob and keep the knob pushedf

3-18Instruments and controlsDo not operate the engine with the pointer ofthe tachometer in the red zone. In this range,fuel injection will be cut by t

16! Interior! Passenger compartment area12453UBF508BB1) Lower anchorages for child re-straint system (page 1-49)2) Seatbelt (page 1-16)3) Center conso

3-19Instruments and controls– CONTINUED –trip knob for 10 seconds or (b) open and close the driv-er’s door, the fuel gauge needle will drop to the “E”

3-20Instruments and controlsWe recommend that you drive moderately until thepointer of the temperature gauge reaches near themiddle of the range. Engi

3-21Instruments and controls– CONTINUED –: Vehicle Dynamics Control operation indicatorlight (if equipped): Vehicle Dynamics Control warning light (if

3-22Instruments and controlsDriver: Instrument panel Front passenger: Between map lights! OperationIf the driver and/or front passenger have/has not y

3-23Instruments and controls– CONTINUED –seconds later (21 seconds after turning ON the ignitionswitch), the warning lights will alternate between fla

3-24Instruments and controlsIf the seatbelt warning device for front passenger’sseat does not function correctly (e.g., it is activatedeven when the f

3-25Instruments and controls– CONTINUED –“ ”: Front passenger’s frontal airbagOFF indicatorThe front passenger’s frontal airbag ON and OFF indi-cators

3-26Instruments and controlsNOTEThis light also comes on when the fuel filler cap isnot tightened until it clicks.If you have recently refueled your v

3-27Instruments and controls– CONTINUED –lubricating system is not working properly.If the light comes on while driving or does not go outafter the en

3-28Instruments and controlsing, you should have your Tire Pressure Moni-toring System checked at a SUBARU dealer assoon as possible.If this light com

This manual describes the following types of the Legacy series.A) Legacy SedanB) Legacy Station wagonC) OUTBACK SedanD) OUTBACK Station wagonABCDUBF20

17– CONTINUED –12 463151 UBF202BB1) Top tether anchorages (page 1-55)2) Dome lights (page 6-2)3) Sun visors (page 6-5)4) Cargo area light (page 6-3)5)

3-29Instruments and controls– CONTINUED –" The warning light does not come on when theignition switch is turned to the “ON” position." The w

3-30Instruments and controls! Brake fluid level warningThis light comes on when the brake fluid level hasdropped to near the “MIN” level of the brake

3-31Instruments and controls– CONTINUED –NOTEThis light does not go out unless the tank is re-plenished up to an internal fuel quantity of about3.7 US

3-32Instruments and controlsvehicle checked at a SUBARU dealer immediately." The light does not come on when the ignition switchis turned to the

3-33Instruments and controls– CONTINUED –sidered normal." The warning light comes on right after the en-gine is started but goes out immediately,

3-34Instruments and controls! SPORT mode indicator light (AT vehicles)This light comes on when the ignition switch is turnedto the “ON” position and g

3-35Instruments and controls– CONTINUED –section in chapter 11.! High beam indicator light This light shows that the headlights are in

3-36Instruments and controlsClockThe clock shows the time while the ignition switch is inthe “ACC” or “ON” position.To adjust the time shown by the cl

3-37Instruments and controls– CONTINUED –Information display (if equipped)With the ignition switch in the “ON” position, each suc-cessive push of the

3-38Instruments and controlsCanada-spec. vehiclesThe outside temperature indicator shows the outsidetemperature in a range from –22 to 122°F (–30 to50

18114 13 121110 9 823 4567UBF510CB1) Parking brake lever (page 7-51)2) Gear shift lever (MT) (page 7-13)3) Select lever (AT) (page 7-16)4) Information

3-39Instruments and controls– CONTINUED –Canada-spec. vehiclesWhen the outside temperature drops to 37°F (3°C) orlower, the temperature indication fla

3-40Instruments and controlsCanada-spec. vehiclesThis indication shows the rate of fuel consumption atthe present moment.! Average fuel consumptionU.S

3-41Instruments and controls– CONTINUED –Canada-spec. vehiclesThis indication shows the average rate of fuel con-sumption since the trip meter was las

3-42Instruments and controlsCanada-spec. vehiclesThe driving range indicates the distance that can bedriven taking into account the amount of fuel rem

3-43Instruments and controls– CONTINUED –Canada-spec. vehiclesIf the driving range is shown as “ ”, there is onlya tiny amount of fuel left in the tan

3-44Instruments and controlsThe journey time indication flashes each time a com-plete hour has elapsed. If the display is giving an indi-cation other

3-45Instruments and controls– CONTINUED –! HeadlightsTo turn on the headlights, turn the knob on the end ofthe turn signal lever.first positionParking

3-46Instruments and controls! Headlight flasherDo not hold the lever in the flashing position formore than just a few seconds.To flash the headlights,

3-47Instruments and controls– CONTINUED –Turn signal leverTo activate the right turn signal, push the turn signal le-ver up. To activate the left turn

3-48Instruments and controlsWhen the control dial is turned upward or downward,the instrument panel’s illumination brightness is indi-cated by the tri

19– CONTINUED –! Instrument panel123456 7 891011121314UBF509CB1) Door locks (page 2-6)2) Illumination brightness control (page 3-47)3) Remote control

3-49Instruments and controls– CONTINUED –Parking light switchThe parking light switch operates regardless of the ig-nition switch position.By pushing

3-50Instruments and controlsFog light switch (if equipped)The front fog lights operate only when the light switchis in the “ ” or “ ” position. To tur

3-51Instruments and controls– CONTINUED –Wiper and washerIn freezing weather, do not use the windshieldwasher until the windshield is sufficientlywarm

3-52Instruments and controlsblades.NOTE" The front wiper motor is protected against over-loads by a circuit breaker. If the motor operatescontinu

3-53Instruments and controls– CONTINUED –! Windshield wipersOFF: Park: IntermittentLO: Low speedHI: High speedTo turn the wipers on, push the wiper co

3-54Instruments and controls! Wiper intermittent time control (if equipped)When the wiper switch is in the “ ” position, turnthe dial to adjust the op

3-55Instruments and controls– CONTINUED –! Rear window wiper and washer switch (Station wagon): Washer (accompanied by wiper operation)ON: ContinuousI

3-56Instruments and controlsWindshield wiper deicer (if equipped)The windshield wiper deicer operates only when theignition switch is in the “ON” posi

3-57Instruments and controls– CONTINUED –Rear window defogger buttonVehicle with manual climate control systemVehicle with automatic climate control s

3-58Instruments and controlsTo turn on the defogger, push the button. To turn it off,push the button again.The indicator light located on the button l

20! Light control and wiper control levers/switches1671110982345UBF512CB1) Parking light switch (page 3-49)2) Windshield wiper (page 3-51)3) Mist (pag

3-59Instruments and controls– CONTINUED –MirrorsAlways check that the inside and outside mirrors areproperly adjusted before you start driving.! Insid

3-60Instruments and controlsdicator light (green) located to the right of the buttonwill illuminate." By pressing and releasing the right button,

3-61Instruments and controls– CONTINUED –! Compass zone adjustment1. The zone setting is factory preset to Zone 8. Referto the “Compass calibration zo

3-62Instruments and controls! Outside mirror defogger (if equipped)Vehicle with manual climate control systemVehicle with automatic climate control sy

3-63Instruments and controls– CONTINUED –switch is turned to the “ACC” or “LOCK” position. If de-frosting or defogging is desired when you restart you

3-64Instruments and controlsplace.5. Make sure that the steering wheel is securelylocked by moving it up and down.HornTo sound the horn, push the horn

4-14Climate controlVentilator ... 4-2Air flow selection ...

4-2Climate controlClimate con trolVentilator! Air flow selectionUB4521BA

4-3Climate control– CONTINUED –! Center and side ventilators! Center ventilatorsMove the tab up and down or right and left to adjust theflow direction

4-4Climate controlManual climate control system (if equipped)! Control panelA) Temperature control dialB) Fan speed control dialC) Air flow control di

21– CONTINUED –! Combination meter! U.S.-spec. vehicles12 356487UBF203BB1) Temperature gauge (page 3-13/page 3-19)2) Tachometer (page 3-11/page 3-17)3

4-5Climate control– CONTINUED –! Fan speed control dialThe fan operates only when the ignition switch isturned to the “ON” position. The fan speed con

4-6Climate control: Air flows through the instrument panel outlets,the windshield defroster outlets, and the foot outlets.: Air flows through the inst

4-7Climate control– CONTINUED –! Air inlet selection buttonON position (Recirculation): Interior air is recirculatedinside the vehicle.Push the air in

4-8Climate controler button will not come on. At the same time, theair inlet selection is automatically set to “outsideair” mode.In this state, you ca

4-9Climate control– CONTINUED –! Bi-level heatingThis setting allows you to direct air of different temper-atures from the instrument panel and foot o

4-10Climate controlNOTEIn a vehicle equipped with an air conditioner, whenthe dial is placed in the “ ” position or “ ”position the air conditioner co

4-11Climate control– CONTINUED –! Control panelA) AUTO buttonB) Temperature control dial (driver’s side)C) Defroster buttonD) Temperature control dial

4-12Climate controlbutton you operated.To change the system back to the AUTO mode, pressthe “AUTO” button.! OFF buttonThe Automatic Climate Control sy

4-13Climate control– CONTINUED –Passenger’s sideIt is possible to make separate temperature settingsfor the driver’s side and passenger’s side. Each t

4-14Climate controlthe system to the setting that was selected before youactivated the defroster.! Fan speed control buttonThe fan speed control butto

22! Canada-spec. vehicles12 356487UBF204BB1) Temperature gauge (page 3-13/page 3-19)2) Tachometer (page 3-11/page 3-17)3) Speedometer (page 3-9/page 3

4-15Climate control– CONTINUED –! Air flow mode selection buttonSelect the desired air flow mode by pushing the airflow mode selection button. The sel

4-16Climate controled, a “ ” indicator light appears on the display. (Outside air): Outside air is drawn into the pas-senger compartment. When the cli

4-17Climate control– CONTINUED –The sensors are located as follows:– Solar sensor: beside windshield defroster grille– Interior air temperature sensor

4-18Climate control! Efficient cooling after parking in direct sunlightAfter parking in direct sunlight, drive with the windowsopen for a few minutes

4-19Climate control– CONTINUED –Air filtration system (if equipped)If your vehicle’s air conditioning system is equippedwith an air filtration system,

5-15AudioAntenna system ... 5-2Printed antenna ... 5-2FM recep

5-2AudioAudioAntenna system! Printed antennaDo not use sharp instruments or window clean-er containing abrasives to clean the inner sur-face of the wi

5-3Audio– CONTINUED –Installation of accessoriesAlways consult your SUBARU dealer before installinga citizen band radio or other transmitting device i

5-4Audio! Type B audio set" Radio operation: refer to page 5-19 " Built-in CD changer operation: refer to page 5-24 ! Type C audio set"

23– CONTINUED –! Warning and indicator lightMark Name PageSeatbelt warning light 3-21SRS airbag system warning light3-24CHECK ENGINE warning light/Mal

5-5Audio– CONTINUED –Type A audio set (if equipped)The audio set will operate only when the ignition switch is in the “ACC” or“ON” position.PUSH POWER

5-6Audio! Radio operation! Power switch and volume controlThe dial is used for both power (ON/OFF) and volumecontrol. The radio is turned ON and OFF b

5-7Audio– CONTINUED –" To change tone control modesEach brief press of the “AUDIO” button changes con-trol modes in the following sequence starti

5-8Audio" To change balance control modeEach brief press of the “BAL” button changes controlmodes in the following sequence starting from volumec

5-9Audio– CONTINUED –! FM/AM selection buttonPush the “FM” or “AM” button when the radio is off toturn on the radio.Push the “FM” or “AM” button when

5-10AudioNOTEWhile you are holding down either side of theTUNE/TRACK button, the tuning frequency will notstop changing even if the frequency of a rec

5-11Audio– CONTINUED –the button, the radio will scan down the frequencyband (from high frequencies to low frequencies).Automatic tuning may not funct

5-12AudioNOTE" DO NOT INSERT TWO DISCS INTO THE DISC IN-SERTION SLOT AT A TIME." Be sure to always insert a disc with the labelside up. If a

5-13Audio– CONTINUED –! To select a song from its beginning" Forward directionBriefly press the “ ” side of the TUNE/TRACK but-ton to skip to the

5-14Audio! Fast-forwarding and fast-reversing" Fast-forwardingPress the “ ” side of the TUNE/TRACK button con-tinuously for more than 0.5 second

24Light indicator light 3-35Low tire pressure warning light (if equipped)3-27Passenger airbag ON indi-cator light3-24Passenger airbag OFF indi-cator l

5-15Audio– CONTINUED –! Repeat playbackUse this to play a certain track repeatedly. Duringplayback, press the “RPT” button. The “RPT” indicatorwill co

5-16AudioNOTEThe random-playback mode will be cancelled ifyou perform any of the following operations:" Press the “RPT” button" Press the “

5-17Audio– CONTINUED –! To eject a disc from the playerWhen a disc is being played back or when a disc is inthe player, press the eject button “ ”. Th

5-18AudioType B audio set (if equipped)The radio will operate only when the ignition switch is in the “ACC” or “ON”position.PUSH POWER-VOLSEEKSCANTUNE

5-19Audio– CONTINUED –! Radio operation! Power switch and volume/bass/treble/fader/balance control" Power switch and volume controlThe dial is us

5-20AudioTo change tone control modes: Each brief press ofthe “AUDIO” button changes control modes in the fol-lowing sequence starting from volume con

5-21Audio– CONTINUED –" To change balance control modesEach brief press of the “BAL” button changes controlmodes in the following sequence starti

5-22Audio! FM/AM selection button (FM/AM)Push the “FM” or “AM” button when the radio is off toturn on the radio.Push the “FM” or “AM” button when the

5-23Audio– CONTINUED –NOTEWhile you are holding down either side of theTUNE/TRACK button, the tuning frequency will notstop changing even if the frequ

5-24Audioto high frequencies). If you hold down the “ ” side ofthe button, the radio will scan down the frequencyband (from high frequencies to low fr

25– CONTINUED –! Trunk/cargo area132231UBF206BB1) Jack handle (page 9-34)2) Jack (page 9-33)3) Spare tire (page 9-3)

5-25Audio– CONTINUED –off." The player is designed to be able to play musicCD-Rs and music CD-RWs, but it may not be ableto play certain ones.! H

5-26Audio" Inserting a disc in a desired position1. Briefly press the “LOAD” button. If the magazine inthe player has an idle position where you

5-27Audio– CONTINUED –" While the player is in the loading mode, if you pressthe “FM” or “AM” button, the player will enter standbymode. Press th

5-28Audio" When there are CDs loaded:Press a desired one of the “Disc select” buttons thedisc number indicator of which steadily lights up. Thepl

5-29Audio– CONTINUED –" Backward directionBriefly press the “ ” side of the TUNE/TRACK but-ton to skip to the beginning of the current track. Eac

5-30Audio" Fast-reversing Press the “ ” side of the TUNE/TRACK button con-tinuously for more than 0.5 second to fast-reverse thedisc.Release the

5-31Audio– CONTINUED –If you accidentally press the button and cancel thetrack-repeat-play mode, press it again to reselectthe repeat play mode."

5-32AudioIf you accidentally press the button and cancel thedisc-repeat-play mode, press it again to reselectthe disc-repeat-play mode." The disc

5-33Audio– CONTINUED –SCAN button" Press the “ ” button" Press the disc select button" Select the radio mode" Turn off the power o

5-34AudioNOTEThe scan mode will be cancelled if you performany of the following steps:" Press the “RPT” button" Press the “RDM” button"

26Function settingsA SUBARU dealer can change the settings of the functions shown below to meet your personal requirements. Con-tact the nearest SUBAR

5-35Audio– CONTINUED –2. Briefly press the “ ” button. The selected discwill be ejected. The disc number indicator will flash atthis time. When you re

5-36Audio" If you press the “ ” button while the player isin all disc ejection mode, the mode will be can-celled following ejection of the disc t

5-37Audio– CONTINUED –Type C audio set (if equipped)The audio set will operate only when the ignition switch is in the “ACC” or“ON” positions.PUSH POW

5-38Audio! Radio operation! Power switch and volume controlThe dial is used for both power (ON/OFF) and volumecontrol. The radio is turned ON and OFF

5-39Audio– CONTINUED –" To change tone control modesEach brief press of the “AUDIO” button changes con-trol modes in the following sequence start

5-40Audio" To change balance control modesEach brief press of the “BAL” button changes controlmodes in the following sequence starting from volum

5-41Audio– CONTINUED –! FM/AM selection buttonPush the “FM” or “AM” button when the radio is off toturn on the radio.Push the “FM” or “AM” button when

5-42AudioNOTEWhile you are holding down either side of theTUNE/TRACK button, the tuning frequency will notstop changing even if the frequency of a rec

5-43Audio– CONTINUED –the button, the radio will scan down the frequencyband (from high frequencies to low frequencies).Automatic tuning may not funct

5-44Audio" After the last song finishes, the disc will auto-matically return to track 1 (the first song on thedisc) and will automatically play b

27– CONTINUED –Windshield wiper deicer (ifequipped)Windshield wiper deicer Operation for 15 min. / ContinuousoperationOperation for15 min.3-56Dome lig

5-45Audio– CONTINUED –" Inserting a disc in a desired position01. Briefly press the “LOAD” button. If the magazine inthe player has an idle posit

5-46Audio" While the player is in the loading mode, if you press“FM” or “AM” button, the player will enter standbymode. Press the “CD” button to

5-47Audio– CONTINUED –" When there are CDs loaded:Press a desired one of the “Disc select” buttons thedisc number indicator of which steadily lig

5-48Audio" Backward directionBriefly press the “ ” side of the TUNE/TRACK but-ton to skip to the beginning of the current track/file(track). Each

5-49Audio– CONTINUED –" Fast-reversing Press the “ ” side of the TUNE/TRACK button con-tinuously for more than 0.5 second to fast-reverse thedisc

5-50Audiobelow.If you accidentally press the button and cancel thetrack/file (track) repeat-play mode, press it againto reselect the repeat-play mode.

5-51Audio– CONTINUED –If you accidentally press the button and cancel thedisc/folder repeat-play mode, press it again to re-select the disc/folder rep

5-52Audio" Press the “ ” or “ ” side of the SEEK/SCANbutton" Press the “ ” button" Press the disc select button" Select the radio

5-53Audio– CONTINUED –! Display selectionIf you press the “TEXT” button for 0.5 second or longerduring playback, the indication will change to the nex

5-54Audio! Folder selectionPress the “ ” side of the SEEK/SCAN button brieflyto select the next folder. Press the “ ” side of thebutton briefly to go

5-55Audio– CONTINUED –2. Briefly press the “ ” button. The selected discwill be ejected. The disc number indicator will flash atthis time. When you re

5-56Audio" If you press the “ ” button while the player isin all disc ejection mode, the mode will be can-celled following ejection of the disc t

5-57Audio– CONTINUED –*: The frequency last received in the selected waveband willbe displayed.! “ ” and “ ” buttons" With radio mode selectedPre

5-58Audio! MUTE buttonPress this button if you wish to immediately cut the vol-ume to zero. The audio display will show “MUTE”.Precautions to observe

5-59Audio– CONTINUED –" In cold and/or rainy weather, dew can form insidethe CD player, preventing normal operation. If thishappens, eject the CD

5-60AudioMP3 audio! What is MP3?MP3 (the name is an abbreviation of ‘MPEG AudioLayer 3’) is a compression format for digital audio. Itwas developed by

5-61Audio– CONTINUED –supported by the audio system. Otherwise, the audiosystem may not play the MP3 files and may not displayfolder titles and file t

6-16Interior equipmentInterior light ... 6-2Dome light ...

6-2Interior equipmentInterior equipmentInterior lightWhen leaving your vehicle, make sure the light isturned off to avoid battery discharge.! Dome lig

1-11Seat, seatbelt and SRS airbagsFront seats ... 1-2Manual seat ...

6-3Interior equipment– CONTINUED –! Cargo area light (Station wagon)The cargo area light switch has three positions:DOOR: The light comes on only when

6-4Interior equipmentVehicle with moonroof (Station wagon) Vehicle without moonroofTo turn on the map light, push the switch. To turn it off,push the

6-5Interior equipment– CONTINUED –Sun visorsTo block out glare, swing down the visors. To use thesun visor at a side window, swing it down and move it

6-6Interior equipmentDo not pull out the extension plate with the sunvisor positioned over the windshield. The ex-tension plate would obstruct your vi

6-7Interior equipment– CONTINUED –Storage compartment" Always keep the storage compartmentclosed while driving to reduce the risk of injuryin the

6-8Interior equipment! Center console boxCenter console box (front)If you remove the divider plate from the dual cuphold-ers, you can use the center c

6-9Interior equipment– CONTINUED –Grasp the dual cupholders’ divider plate at the base.Turn it counterclockwise to remove it.If you hold the divider p

6-10Interior equipmentCenter console box (rear)Pull up the lock release knob at the bottom of the frontedge of the lid.! Center panel compartmentWhen

6-11Interior equipment– CONTINUED –! Overhead console (if equipped)To open the console, push on the lid lightly and it willautomatically open.When you

6-12Interior equipment! Front passenger’s cup holderThe dual cup holder is built into the center consolenear the parking brake lever.To access the cup

1-2Seat, seatbelt and SRS airbagsSeat, seat belt and SRS airba gsFront seats" Never adjust the seat while driving to avoidthe possibility of loss

6-13Interior equipment– CONTINUED –! Rear passenger’s cup holderThe rear passenger’s cup holder is located on the low-er side of the back of the cente

6-14Interior equipmentAccessory power outletsAccessory power outlets are provided in the centerconsole and in the cargo area.Electrical power (12V DC)

6-15Interior equipment– CONTINUED –accessory power outlet." Do not place any foreign objects, especiallymetal ones such as coins or aluminum foil

6-16Interior equipmentCigarette lighter socketA cigarette lighter socket can be found behind the ash-tray lid under the climate controls. Push gently

6-17Interior equipment– CONTINUED –! Use with a cigarette lighterThe cigarette lighter operates only when the ignitionswitch is in the “ON” and “ACC”

6-18Interior equipmentTo use the cigarette lighter, push in the knob and waita few moments. It will automatically spring up whenready for use.To avoid

6-19Interior equipment– CONTINUED –used in the socket. If you want to use the socket for acigarette lighter again, or to protect your purchaser be-for

6-20Interior equipmentTo open the ashtray, push lightly on the lid below theclimate controls.Fully close the lid after using it to help reduce residua

6-21Interior equipment– CONTINUED –The coat hook is attached to each rear passenger’shand grip.Shopping bag hookDo not hang items on the shopping bag

6-22Interior equipment! For Station wagon modelsA shopping bag hook is attached to each side of thecargo area.To use the hook, push the upper portion

1-3Seat, seatbelt and SRS airbags– CONTINUED –restrained or improperly restrained. Becausechildren are lighter and weaker than adults,their risk of be

6-23Interior equipment– CONTINUED –Make sure the driver’s floor mat is placed backin its proper location and correctly secured onits retaining pin. If

6-24Interior equipmentis rewinding.Do not place anything on the extended cover.Putting excessive weight on the extended cov-er can break it and an obj

6-25Interior equipment– CONTINUED –2. Hold both sides of the bottom edge of the rear gateboard, rotate the rear gate board toward you, and pullit out

6-26Interior equipment2. To keep the lid open, hang the hook (provided onthe back of the lid) on the rear edge of the roof.3. Remove the left and righ

6-27Interior equipment– CONTINUED –! To install the rear gate boardInsert (tipped at an angle) the hooks on the rear gateboard into the holes in the r

6-28Interior equipmentFit the top of the rear gate board into the groove in therear gate panel.Stowage boxes (Station wagon)A stowage box is located o

6-29Interior equipment– CONTINUED –Convenient tie-down hooks (if equipped)The convenient tie-down hooks are designedonly for securing light cargo. Nev

6-30Interior equipmentUnder-floor storage compartmentThe subfloor storage is located under the floor of thetrunk or cargo area and can be used to stor

6-31Interior equipment– CONTINUED –! Station wagonHang the hook provided on the underside of the lid onthe rear edge of the roof to keep the lid open.

6-32Interior equipmentcurity systems. There are three HomeLink® buttonson the sun visor, each of which you can program foroperation of one desired dev

1-4Seat, seatbelt and SRS airbags! Reclining the seatbackTo prevent the passenger from sliding underthe seatbelt in the event of a collision, alwayspu

6-33Interior equipment– CONTINUED –hand-held transmitters for further programming ordevice testing in the event of a problem." It is recommended

6-34Interior equipment4. Using both hands, simultaneously push the hand-held transmitter button and the desired HomeLink®button. DO NOT release the bu

6-35Interior equipment– CONTINUED –1. Locate the training button on the garage door open-er motor head unit. The exact location and color of thebutton

6-36Interior equipment4. The garage door opener should now recognize theHomeLink® Wireless Control System and your garagedoor opener should activate w

6-37Interior equipment– CONTINUED –rapidly after several seconds, release both buttons.7. Plug the motor of the entrance gate/garage dooropener to the

6-38Interior equipment2. Release both buttons.! In case a problem occursIf you cannot activate a device using the correspond-ing HomeLink® button afte

7-17Starting and operatingFuel ... 7-2Fuel requirements ...

7-2Starting and operatingStarting and ope ratingFuelUse of a fuel which is low in quality or use of aninappropriate fuel additive may cause enginedama

7-3Starting and operating– CONTINUED –Standards as indicated on the underhood tune-up la-bel. It is designed to optimize engine and emissioncontrol sy

7-4Starting and operatingIn addition, some gasoline suppliers are now produc-ing reformulated gasolines, which are designed to re-duce vehicle emissio

1-5Seat, seatbelt and SRS airbags– CONTINUED –! Seat cushion height adjustment (driver’s seat)The height of the seat can be adjusted by moving theseat

7-5Starting and operating– CONTINUED –1. To open the fuel filler lid, pull the lid release leverup.2. Open the fuel filler lid.UB7205BAUB7500BA

7-6Starting and operatingA) OpenB) Close3. Remove the fuel filler cap by turning it slowly coun-terclockwise." Gasoline vapor is highly flammable

7-7Starting and operating– CONTINUED –" You will see the “ ” sign in the combinationmeter. This indicates that the fuel filler door (lid) islocat

7-8Starting and operatingState emission testing (U.S. only)Testing of an All-Wheel Drive vehicle mustNEVER be performed on a single two-wheel dy-namom

7-9Starting and operating– CONTINUED –jacked off the ground, nor should the driveshaft be dis-connected for state emission testing.The EPA has issued

7-10Starting and operatingPreparing to driveYou should perform the following checks and adjust-ments every day before you start driving.1. Check that

7-11Starting and operating– CONTINUED –If the engine does not start, try the following:1)Turn the ignition switch to the “OFF” position andwait for at

7-12Starting and operatingRelease the accelerator pedal as soon as the en-gine starts.2)If this fails to start the engine, turn the ignitionswitch bac

7-13Starting and operating– CONTINUED –Manual transmissionDo not drive the vehicle with the clutch disen-gaged (i.e., when the clutch pedal is depress

7-14Starting and operating! Shifting speeds! Recommended shifting speedsThe best compromise between fuel economy and ve-hicle performance during norma

1-6Seat, seatbelt and SRS airbags! Reclining the seatbackTo prevent the passenger from sliding underthe seatbelt in the event of a collision, alwayspu

7-15Starting and operating– CONTINUED –Turbo modelsmph (km/h)Never exceed posted speed limits.! Driving tipsDo not drive with your foot resting on the

7-16Starting and operatingAutomatic transmission – 4 speedThe automatic transmission is electronically controlledand provides 4 forward speeds and 1 r

7-17Starting and operating– CONTINUED –! Selector lever: Shift possible with brake pedal depressed: Shift possible with brake pedal not depressedThe s

7-18Starting and operatingthe selector lever to the “P” position.Do not drive the vehicle with the selector leverin the “N” (neutral) position. Engine

7-19Starting and operating– CONTINUED –risen to a certain level, automatic downshift nor-mally takes place. In the meantime, downshiftmanually for eng

7-20Starting and operatinginto the hole, move the selector lever to the “P” posi-tion. If the selector lever reverse inhibiting functionfails, have th

7-21Starting and operating– CONTINUED –goes off.Gearshifts can be performed using the selector lever.Using the selector leverShift to the next-higher

7-22Starting and operatingnot travelling at a speed exceeding the Maxi-mum Allowable Speed for the gear which isabout to be selected. Failure to obser

7-23Starting and operating– CONTINUED –! Driving tips" On a road surface where there is a risk of wheelspin(for example, a snow- or gravel-covere

7-24Starting and operatingWhen selected, the SPORT mode indicator light onthe instrument panel will turn on. To deselect SPORT mode, move the selector

1-7Seat, seatbelt and SRS airbags– CONTINUED –! Seat cushion angle adjustment (Driver’s seat only)To adjust the seat cushion angle, pull up or push do

7-25Starting and operating– CONTINUED –4. Insert the screwdriver into the hole.5. Push down on the screwdriver and move the selec-tor lever from the “

7-26Starting and operatingtil the vehicle has completely stopped. Suchshifting may cause damage to the transmis-sion.NOTEImmediately after ATF (automa

7-27Starting and operating– CONTINUED –fully, then shift into the “P” position. Do not hold the ve-hicle with only the transmission.To shift the selec

7-28Starting and operatingWhen more acceleration is required in this position,press the accelerator pedal fully to the floor and holdthat position. Th

7-29Starting and operating– CONTINUED –Once operational, it prevents the selector lever frombeing moved from the “N” position to the “R” position.When

7-30Starting and operating! Selection of manual modeWith the vehicle either moving or stationary, move theselector lever from the “D” position to the

7-31Starting and operating– CONTINUED –goes off.Gearshifts can be performed using the selector leveror the shift switch on the steering wheel (turbo m

7-32Starting and operatingIf you subsequently ease off the accelerator pedal andthen accelerate again, the transmission will automati-cally switch bac

7-33Starting and operating– CONTINUED –ing caused by down shifting when the vehicle istravelling on a slippery surface can lead towheel locking; as a

7-34Starting and operatinga standstill. This phenomenon does not indicate afault.! SPORT modeSPORT mode is used when power is needed for rapidaccelera

1-8Seat, seatbelt and SRS airbags! Head restraint adjustmentTo raise the head restraint, pull it up. To lower it, pushthe head restraint down while pr

7-35Starting and operating– CONTINUED –! Shift lock releaseIf the selector lever does not move from the “P” posi-tion with the brake pedal depressed a

7-36Starting and operatingRear viscous limited slip differential (LSD) (if equipped)" Never start the engine while a tire on one sideis jacked up

7-37Starting and operating– CONTINUED –Braking! Braking tipsNever rest your foot on the brake pedal whiledriving. This can cause dangerous overheating

7-38Starting and operatingthan normal and the braking distance will increase.! Disc brake pad wear warning indica-torsThe disc brake pad wear warning

7-39Starting and operating– CONTINUED –The ABS system prevents the lock-up of wheels whichmay occur during sudden braking or braking on slip-pery road

7-40Starting and operating" The warning light does not come on when theignition switch is turned to the “ON” position." The warning light co

7-41Starting and operating– CONTINUED –Electronic Brake Force Distribution (EBD) systemThe EBD system maximizes the effectiveness of thebrakes by allo

7-42Starting and operatinglight illuminate simultaneously, take the followingsteps:1. Stop the vehicle in the nearest safe, flat place.2. Shut down th

7-43Starting and operating– CONTINUED –Vehicle Dynamics Control system (if equipped)Always use the utmost care in driving – over-confidence because yo

7-44Starting and operatingspinning of the driving wheels on slippery road surfac-es, thereby helping to maintain traction and directionalcontrol. Acti

1– CONTINUED –Warranties! Warranties for U.S.A.All SUBARU vehicles distributed by Subaru of Ameri-ca, Inc. and sold at retail by an authorized SUBARUd

1-9Seat, seatbelt and SRS airbags– CONTINUED –" Each active head restraint is effective onlywhen its height is properly adjusted and theuser sits

7-45Starting and operating– CONTINUED –snow chains, however, the effectiveness of the Ve-hicle Dynamics Control system is reduced andthis should be ta

7-46Starting and operatingshould occur, have an authorized SUBARU dealercarry out an inspection of that system at the first avail-able opportunity.&qu

7-47Starting and operating– CONTINUED –trols each brake through the ABS, whenever the ABSstops operating due to a malfunction in that electricalsystem

7-48Starting and operating! Vehicle Dynamics Control OFF switchPressing the switch to deactivate the Vehicle Dynam-ics Control system can facilitate t

7-49Starting and operating– CONTINUED –Tire pressure monitoring system (TPMS) (if equipped)The tire pressure monitoring system provides the driv-er wi

7-50Starting and operatingoff a few minutes later.If this light still comes on while driving after ad-justing the tire pressure, a tire may have signi

7-51Starting and operating– CONTINUED –Parking your vehicle" Never leave unattended children or pets inthe vehicle. They could accidentally injur

7-52Starting and operating“Warning and indicator lights” section (chapter 3).When parking your vehicle, always set the parkingbrake firmly and put the

7-53Starting and operating– CONTINUED –Cruise controlCruise control enables you to maintain a constant ve-hicle speed without holding your foot on the

7-54Starting and operatingThe “ ” indicator light on the combinationmeter will come on.2. Depress the accelerator pedal until the vehiclereaches the d

1-10Seat, seatbelt and SRS airbagsSeat heater (if equipped)The seat heater operates when the ignition switch iseither in the “ACC” or “ON” position.Ea

7-55Starting and operating– CONTINUED –At this time, the “ ” indicator light is illuminated inthe combination meter.The vehicle will maintain the desi

7-56Starting and operatingcruising speed automatically.The “ ” indicator light in the combination meter willautomatically come on at this time.! To tu

7-57Starting and operating– CONTINUED –! To decrease the speed (by control lever)Push the control lever downward in the “SET/COAST”direction and hold

7-58Starting and operatingThe light comes on when the “CRUISE” main switch ispressed.If you move the cruise control lever while turning theignition sw

8-18Driving tipsNew vehicle break-in driving – the first 1,000 miles (1,600 km) ... 8-2Fuel economy hints ...

8-2Driving tipsDriving tipsNew vehicle break-in driving – the first 1,000 miles (1,600 km)The performance and long life of your vehicle are de-pendent

8-3Driving tips– CONTINUED –Engine exhaust gas (Carbon monox-ide)" Never inhale engine exhaust gas. Engine ex-haust gas contains carbon monoxide,

8-4Driving tipsCatalytic converter" Avoid fire hazards. Do not drive or park thevehicle anywhere near flammable materials(e.g. grass, paper, rags

8-5Driving tips– CONTINUED –2.5-liter turbo models 2.5-liter non-turbo models (California-spec.) and 3.0-liter modelsThe catalytic converter is instal

8-6Driving tips" Keep your engine tuned-up. If you feel the enginerunning rough (misfiring, backfiring or incompletecombustion), have your vehicl

1-11Seat, seatbelt and SRS airbags– CONTINUED –Rear seatsSeatbelts provide maximum restraint when theoccupant sits well back and upright in the seat.D

8-7Driving tips– CONTINUED –Driving in foreign countriesWhen planning to use your vehicle in another country:" Confirm the availability of the co

8-8Driving tipsAll wheel drive distributes the engine power to all fourwheels. AWD vehicles provide better traction whendriving on slippery, wet or sn

8-9Driving tips– CONTINUED –" There are some precautions that you must observewhen towing your vehicle. For detail information, see“Towing” secti

8-10Driving tipsnext section (applicable to the OUTBACK) for generalguidance. But please keep in mind that your vehicle’soff-road capabilities are mor

8-11Driving tips– CONTINUED –" Always check your brakes for effectiveness immedi-ately after driving in sand, mud or water. Do this bydriving slo

8-12Driving tipsWinter driving! Operation during cold weatherCarry some emergency equipment, such as tirechains, a window scraper, a bag of sand, flar

8-13Driving tips– CONTINUED –! Parking in cold weatherSnow can trap dangerous exhaust gases underyour vehicle. Keep snow clear of the exhaustpipe and

8-14Driving tipsing, abrupt acceleration, high-speed driving, andsharp turning when driving on snowy or icy roads.Always maintain ample distance betwe

8-15Driving tips– CONTINUED –! Snow tires! All models except OUTBACK" When replacing original tires with winter(snow) tires, make sure you use on

8-16Driving tipsous and lead to loss of vehicle control." You must install four winter tires that are ofthe same size, circumferences, constructi

1-12Seat, seatbelt and SRS airbags! Folding down the rear seat – Station wagon" After returning the rear seat to its original po-sition, be certa

8-17Driving tips– CONTINUED –! Tire chainsTire chains cannot be used on tires listed belowbecause of lack of clearance between the tiresand vehicle bo

8-18Driving tipsLoading your vehicleNever allow passengers to ride on the foldedrear seatback, in the trunk or in the cargo area.Doing so may result i

8-19Driving tips– CONTINUED –Do not carry spray cans, containers with flam-mable or corrosive liquids or any other danger-ous items inside the vehicle

8-20Driving tips! GVWR and GAWR (Gross Vehicle Weight Rating and Gross Axle Weight Rating)Certification labelThe certification label attached to the d

8-21Driving tips– CONTINUED –! Roof rail and crossbar (if equipped)A) Crossbar kit" For cargo carrying purposes, the roof railmust be used togeth

8-22Driving tips! Installing carrying attachments on the cross-barsWhen installing any carrying attachment such as abike carrier, ski carrier, kayak c

8-23Driving tips– CONTINUED –2. Carefully raise the crossbar from roof rails." To install the front crossbarFront crossbar:Front crossbar has 100

8-24Driving tips3. The crossbar with the 100 LBS Load Label at-tached onto it is the front crossbar. An arrow is markedon the back of the front crossb

8-25Driving tips– CONTINUED –A) Lower clampB) T-30 torx® head screw5. Tighten the lower clamps onto the crossbar. Usinga torque wrench, loosely tight

8-26Driving tipsRear crossbar:A) Zero gapInstall the rear cross bar so that the rear edges of bothcrossbar end supports are aligned (zero gap) with th

1-13Seat, seatbelt and SRS airbags– CONTINUED –the vehicle is struck from the rear.! Rear windows side seating positionTo raise the head restraint, pu

8-27Driving tips– CONTINUED –Trailer hitch (if equipped)" Never exceed the maximum weight specifiedfor the trailer hitch. Exceeding the maximumwe

8-28Driving tips2. Insert the hitch pin into the hole on the hitch receiv-er tube so that the pin passes through the ball mount.3. Insert the safety p

8-29Driving tips– CONTINUED –A) Hitch ball installation pointB) Hooks for safety chains5. Use only a hitch ball that is appropriate for the ballmount

8-30Driving tipsHitch harness connector8. Connect the hitch wire harness’s black four-pinwire connector to the towing trailer’s wire harness.9. Confir

8-31Driving tips– CONTINUED –Trailer towingYour vehicle is designed and intended to be used pri-marily as a passenger-carrying vehicle. Towing a trail

8-32Driving tipsand trailer are acceptable.! Total trailer weightTotal trailer weightThe total trailer weight (trailer weight plus its cargoload) must

8-33Driving tips– CONTINUED –All models other than 3.0-liter models! Gross Vehicle Weight (GVW) and Gross Vehicle Weight Rating (GVWR)Gross Vehicle We

8-34Driving tipsthe driver’s door of your vehicle.Certification label! Gross Axle Weight (GAW) and Gross Axle Weight Rating (GAWR)Gross Axle WeightThe

8-35Driving tips– CONTINUED –Certification labelTo check both GVWR and GAWR and to confirm thatthe total weight and weight distribution are within saf

8-36Driving tipsEnsure that the trailer tongue load is from 8 to 11 per-cent of the total trailer weight and does not exceed themaximum value of 200 l

1-14Seat, seatbelt and SRS airbagsplace the head restraint in its highest position. Whenthe rear center seating position is not occupied, lowerthe hea

8-37Driving tips– CONTINUED –! Trailer hitchesNever drill the frame or under-body of your ve-hicle to install a commercial trailer hitch. If youdo, da

8-38Driving tips! Connecting a trailer! Trailer brakes" Adequate size trailer brakes are requiredwhen the trailer and its cargo exceed 1,000 lbs(

8-39Driving tips– CONTINUED –! Side mirrorsAfter hitching a trailer to your vehicle, check that thestandard side mirrors provide a good rearward field

8-40Driving tipsand in “GAS STATION REFERENCE” at the end ofthis manual. Adjust the rear tire pressure to the recom-mended pressure when the tires are

8-41Driving tips– CONTINUED –" Sufficient time should be taken to learn the “feel” ofthe vehicle/trailer combination before starting out on atrip

8-42Driving tips! Driving on grades" Before going down a steep hill, slow down and shiftinto lower gear (if necessary, use 1st gear) in order tou

9-19In case of emergencyIf you park your vehicle in an emergency .. 9-2Temporary spare tire ... 9-3Flat tires ...

9-2In case of emergencyIn case o f emergen cyIf you park your vehicle in an emer-gencyThe hazard warning flasher should be used in day ornight to warn

9-3In case of emergency– CONTINUED –Temporary spare tire" Never tow a trailer when the temporary sparetire is used. The temporary spare tire is n

9-4In case of emergency1) Tread wear indicator bar2) Indicator location mark" When the wear indicator appears on the tread, re-place the tire.NOT

1-15Seat, seatbelt and SRS airbags– CONTINUED –Station wagonTo lower the armrest, pull on the top edge of the arm-rest.To avoid the possibility of ser

9-5In case of emergency– CONTINUED –Flat tiresIf you have a flat tire while driving, never brake sud-denly; keep driving straight ahead while graduall

9-6In case of emergencySedanA) Jack handleB) Spare tireC) Jack and tool bucketStation wagonA) Jack handleB) Jack and tool bucketC) Spare tire5. Take o

9-7In case of emergency– CONTINUED –Sedan:1. Lift the handle of the floor cover and hook the han-dle onto the trunk edge.2. Remove the jack handle fro

9-8In case of emergency4. Take out the jack and tool bucket.A) Wheel nut wrenchB) Jack5. Take the wheel nut wrench and jack out of the toolbucket.UB92

9-9In case of emergency– CONTINUED –6. Turn the attaching bolt counterclockwise, then takethe spare tire out.Station wagon:1. Open the lid and hang t

9-10In case of emergency2. Remove the left hand part of the lid and take out thejack handle.3. Take out the storage tray.UB9504BA UB6531BA

9-11In case of emergency– CONTINUED –4. Take out the jack and tool bucket.A) Wheel nut wrenchB) Jack5. Take the wheel nut wrench and jack out of the t

9-12In case of emergency6. Turn the attaching bolt counterclockwise, then takespare tire out.If the spare tire provided in your vehicle is a temporary

9-13In case of emergency– CONTINUED –8. Place the jack under the side sill at the front or rearjack-up point closest to the flat tire.Turn the jackscr

9-14In case of emergency9. Insert the jack handle into the jackscrew, and turnthe handle until the tire clears the ground. Do not raisethe vehicle hig

1-16Seat, seatbelt and SRS airbagsand heavier than 55 lbs (25 kg). Such objectscan interfere with the driver’s proper operationof the vehicle, possibl

9-15In case of emergency– CONTINUED –surface of the wheel and hub with a cloth.12.Put on the spare tire. Replace the wheel nuts.Tighten them by hand.D

9-16In case of emergencycations.Never place a tire or tire changing tools in thepassenger compartment after changingwheels. In a sudden stop or collis

9-17In case of emergency– CONTINUED –When a spare tire is mounted or a wheel rim isreplaced without the original pressure sensor/transmitter being tra

9-18In case of emergencyDo not jump start unless cables in suitable con-dition are available." A running engine can be dangerous. Keepyour finger

9-19In case of emergency– CONTINUED –(1)(4)(2)(3)UB9521BB1)Connect one jumper cable to thepositive (+) terminal on the dis-charged battery.2)Connect t

9-20In case of emergency5. Start the engine of the vehicle with the booster bat-tery and run it at moderate speed. Then start the en-gine of the vehic

9-21In case of emergency– CONTINUED –Confirm that the cooling fan is turning. If the fan is notturning, immediately turn the engine off and contactyou

9-22In case of emergencydealer or a commercial towing service. Observe thefollowing procedures for safety.! Towing and tie-down hooksThe towing hooks

9-23In case of emergency– CONTINUED –4. Screw the towing hook into the thread hole until thethreads can no longer be seen.5. Tighten the towing hook s

9-24In case of emergency2. Wrap a flat-head screwdriver with cloth or vinyl.Then, insert the screwdriver into the gap between thefog light cover and t

1-17Seat, seatbelt and SRS airbags– CONTINUED –cially if they are 12 years of age and under andare not restrained or improperly restrained. Be-cause c

9-25In case of emergency– CONTINUED –5. Screw the towing hook into the thread hole until thethreads can no longer be seen.6. Tighten the towing hook s

9-26In case of emergencythe SRS airbag system in a frontal collision.Rear towing hook:The rear towing hook is located below the center of therear bump

9-27In case of emergency– CONTINUED –Rear tie-down hooks:The rear tie-down hooks are located near each of thejack-up reinforcements.Use the rear tie-d

9-28In case of emergency! Towing with all wheels on the ground" Never turn the ignition switch to the “LOCK”position while the vehicle is being t

9-29In case of emergency– CONTINUED –Rear gate – if the rear gate cannot be unlockedIn the event that you cannot unlock the rear gate byoperating the

9-30In case of emergencyMoonroof – if the moonroof cannot be closedIf the moonroof cannot be closed with the moonroofswitch, you can close the moonroo

9-31In case of emergency– CONTINUED –4. Insert the wrench in the end of the motor shaft.To lower the moonroof, turn the wrench clockwise.To close the

9-32In case of emergency2)Use a screwdriver or similar implement to sepa-rate the slider and rod. Slide the sun shade towardthe front of the vehicle.3

9-33In case of emergency– CONTINUED –4. Insert the wrench in the end of the motor shaft.To close the moonroof, turn the wrench clockwise.Have your veh

9-34In case of emergencyStation wagon: To take out the jack and maintenancetools, open the center lid and remove the bucket fromthe center of the spar

1-18Seat, seatbelt and SRS airbags! Expectant mothersExpectant mothers also need to use the seatbelts.They should consult their doctor for specific re

9-35In case of emergency– CONTINUED –Station wagon: Open the center lid, remove the lefthand part of the lid, and take out the jack handle.For how to

9-36In case of emergencyNOTEWhen you first receive your vehicle from yourdealer, the hex-headed wrench is stored in theglove box. We recommend that yo

10-110Appearance careExterior care ... 10-2Washing ...

10-2Appearance careAppearan ce careExterior care! Washing" When washing the vehicle, the brakes mayget wet. As a result, the brake stopping dis-t

10-3Appearance care– CONTINUED –the mud and sand off the underbody.Carefully flush the suspension and axle parts, as theyare particularly prone to mud

10-4Appearance care! Cleaning aluminum wheels" Promptly wipe the aluminum wheels clean of anykind of grime or agent. If dirt is left on too long,

10-5Appearance care– CONTINUED –proper ventilation.! To help prevent corrosionWash the vehicle regularly to prevent corrosion of thebody and suspensio

10-6Appearance careCleaning the interiorUse a vacuum cleaner to get rid of the dust and dirt.Wipe the vinyl areas with a clean, damp cloth.! Seat fabr

10-7Appearance care– CONTINUED –NOTEStrong cleaning agents such as solvents, paintthinners, window cleaner or gasoline must neverbe used on leather or

2How to use this owner’s manual! Using your Owner’s manualBefore you operate your vehicle, carefully read thismanual. To protect yourself and extend t

1-19Seat, seatbelt and SRS airbags– CONTINUED –! Seatbelt warning light and chime Your vehicle is equipped with a seatbelt warning de-vice at the

11-111Maintenance and serviceMaintenance schedule ... 11-3Maintenance precautions ... 11-3Bef

11-2Maintenance and serviceBreaking-in of new brake pads and linings ... 11-47Parking brake stroke ... 11-48Tires an

11-3Maintenance and service– CONTINUED –Maintenance a nd serviceMaintenance scheduleThe scheduled maintenance items required to be ser-viced at regula

11-4Maintenance and servicethe materials in the vehicle may be hazardous ifimproperly used or handled, for example, bat-tery acid." Your vehicle

11-5Maintenance and service– CONTINUED –even when the engine is stopped.! When you do checking or servicing in the engine compartment while the en-gin

11-6Maintenance and service3. Release the secondary hood release located underthe front grille by moving the lever toward the left. 4. Lift up the hoo

11-7Maintenance and service– CONTINUED –it. It could deform the metal.Always check that the hood is properly lockedbefore you start driving. If it is

11-8Maintenance and serviceEngine compartment overview! 2.5-liter non-turbo models12 345678910111312UBB207BB1) Power steering fluid reservoir (page 11

11-9Maintenance and service– CONTINUED –! 2.5-liter non-turbo California-spec. models123456789101113 12UBB202BB1) Power steering fluid reservoir (page

11-10Maintenance and service! 2.5-liter turbo models12 463513 12 11 10 9 8 7UBB203BB1) Power steering fluid reservoir (page 11-41)2) Manual transmissi

1-20Seat, seatbelt and SRS airbagsseconds later (21 seconds after turning ON the ignitionswitch), the warning lights will alternate between flash-ing

11-11Maintenance and service– CONTINUED –! 3.0-liter models12 34512 1011 9 876UBB564BB1) Power steering fluid reservoir (page 11-41)2) Differential ge

11-12Maintenance and serviceEngine oil! Checking the oil levelCheck the engine oil level at each fuel stop.1. Park the vehicle on a level surface and

11-13Maintenance and service– CONTINUED –3.0-liter modelsA) Upper levelB) Lower level4. Pull out the dipstick again and check the oil level onit. If i

11-14Maintenance and service2. Park the vehicle on a level surface and stop the en-gine.3. Remove the oil filler cap.2.5-liter turbo modelsOther model

11-15Maintenance and service– CONTINUED –washer after the oil has completely drained out.6. Remove the under cover.7. Remove the oil filter with an oi

11-16Maintenance and service! Recommended grade and viscosityUse only engine oil with the recommendedgrade and viscosity.Oil grade:ILSAC GF-3, which c

11-17Maintenance and service– CONTINUED –API Service labelA) Indicates the oil quality by API designationsB) Indicates the SAE oil viscosity gradeC) I

11-18Maintenance and serviceAPI classification SL (or SJ):SAE viscosity No.:30, 40, 10W-50, 20W-40, 20W-50Cooling systemNever attempt to remove the ra

11-19Maintenance and service– CONTINUED –ed parts. The alcohol contained in the enginecoolant may damage the paint surface.! Hose and connectionsYour

11-20Maintenance and serviceA) Rubber gaskets3. After refilling the reserve tank and the radiator, re-install the caps and check that the rubber gaske

1-21Seat, seatbelt and SRS airbags– CONTINUED –seats only)If the seatbelt warning device for front passenger’sseat does not function correctly (e.g.,

11-21Maintenance and service– CONTINUED –loosen the drain plug.3. Loosen the radiator cap to drain the coolant fromthe radiator. Then drain the coolan

11-22Maintenance and serviceTurbo modelsA) Fill up to here5. Slowly pour the coolant and fill up to just below thefiller neck, allowing enough room to

11-23Maintenance and service– CONTINUED –6. Pour the coolant and fill to the reservoir tank’s“FULL” level mark.A) Rubber gaskets7. Put the radiator ca

11-24Maintenance and serviceAir cleaner elementDo not operate the engine with the air cleanerelement removed. The air cleaner element notonly filters

11-25Maintenance and service– CONTINUED –5. Open the air cleaner case cover and remove the aircleaner element.6. Clean the inside of the air cleaner c

11-26Maintenance and service! Turbo models01. Use a screwdriver to undo the clips on the air intakeduct, then remove the air intake duct.2. Unplug the

11-27Maintenance and service– CONTINUED –3. Use a screwdriver to remove the duct that is con-nected to the air cleaner case cover.4. Unsnap the two cl

11-28Maintenance and service5. Open the air cleaner case cover and remove the aircleaner element.6. Clean the inside of the air cleaner cover and case

11-29Maintenance and service– CONTINUED –Spark plugs" When disconnecting the spark plug cables,always grasp the spark plug cap, not the ca-bles.&

11-30Maintenance and serviceDrive beltsThe alternator, power steering pump, and air condi-tioner compressor depend on drive belts. Satisfactoryperform

1-22Seat, seatbelt and SRS airbagsNever place the shoulder belt under the arm orbehind the back. If an accident occurs, this canincrease the risk or s

11-31Maintenance and service– CONTINUED –Manual transmission oil! Checking the oil levelNon-turbo modelsA) Yellow handleTurbo models1. Park the vehicl

11-32Maintenance and serviceA) Upper levelB) Lower level3. Pull out the dipstick again and check the oil level onit. If it is below the lower level, a

11-33Maintenance and service– CONTINUED –Automatic transmission fluid! Checking the fluid levelThe automatic transmission fluid expands largely asits

11-34Maintenance and service5 speed automatic transmissionA) Yellow handleA) HOT rangeB) COLD rangeC) Upper levelD) Lower level4. Pull out the dipstic

11-35Maintenance and service– CONTINUED –fluid up to the upper level. Be careful not to overfill.! Recommended fluidUse one of the following types of

11-36Maintenance and serviceA) Upper levelB) Lower level3. Pull out the dipstick again and check the oil level onit. If it is below the lower level, a

11-37Maintenance and service– CONTINUED –Rear differential gear oil! Checking the gear oil levelIf the vehicle requires frequent refilling, theremay b

11-38Maintenance and service2.5i (AT)A) Filler holeB) Drain holeC) Oil level2.5-liter turbo and 3.0-liter models (AT)A) Filler plugB) Drain plugABCUSB

11-39Maintenance and service– CONTINUED –2.5-liter turbo and 3.0-liter models (AT)A) Filler holeB) Drain holeC) Oil levelOthersA) Filler plugB) Drain

11-40Maintenance and serviceOthersA) Filler holeB) Drain holeC) Oil levelRemove the plug from the filler hole and check the oillevel. The oil level sh

1-23Seat, seatbelt and SRS airbags– CONTINUED –4. Insert the tongue plate into the buckle until youhear a click.5. To make the lap part tight, pull up

11-41Maintenance and service– CONTINUED –Power steering fluid! Checking the fluid levelBe careful not to burn yourself because the flu-id may be hot.&

11-42Maintenance and service! Recommended fluid“Dexron III” Type Automatic Transmission FluidBrake fluid! Checking the fluid level" Never let bra

11-43Maintenance and service– CONTINUED –faces or rubber parts. Alcohol contained in thebrake fluid may damage them.Check the fluid level monthly.Chec

11-44Maintenance and serviceCheck the fluid level on the outside of the reservoir. Ifthe level is below “MIN” level mark, add the recom-mended clutch

11-45Maintenance and service– CONTINUED –Brake pedalCheck the brake pedal free play and reserve distanceaccording to the maintenance schedule in the “

11-46Maintenance and serviceClutch pedal (Manual transmission vehicles)Check the clutch pedal free play and reserve distanceaccording to the maintenan

11-47Maintenance and service– CONTINUED –Replacement of brake pad and liningIf you continue to drive despite the scrapingnoise from the audible brake

11-48Maintenance and servicemay cause the rear wheels to lock. To avoidthis, be certain to pull the lever up slowly andgently.1. Drive the vehicle at

11-49Maintenance and service– CONTINUED –Tires and wheels! Types of tiresYou should be familiar with type of tires present onyour vehicle.! All season

11-50Maintenance and servicefollowing table shows the required tire pressures thatcorrespond to various outside temperatures when thetemperature in th

1-24Seat, seatbelt and SRS airbags" Adjusting the front seat shoulder belt anchor heightThe shoulder belt anchor height should be adjusted tothe

11-51Maintenance and service– CONTINUED –fore, you should have the work performed by a SUBA-RU dealer.If the low tire pressure warning light does notc

11-52Maintenance and serviceit difficult to steer the vehicle in a straight line, oneof the tires and/or wheels may be damaged. Driveslowly to the nea

11-53Maintenance and service– CONTINUED –Incorrect tire pressures detract from controllability andride comfort, and they cause the tires to wear abnor

11-54Maintenance and service" Abnormally high tire pressure (tread worn in cen-ter)Ride comfort is poor. Also, the tire magnifies the ef-fects of

11-55Maintenance and service– CONTINUED –! Wear indicatorsA) New treadB) Worn treadC) Tread wear indicatorEach tire incorporates a tread wear indicato

11-56Maintenance and serviceTire wear varies from wheel to wheel. To maximize thelife of each tire and ensure that the tires wear uniform-ly, it is be

11-57Maintenance and service– CONTINUED –tires. Doing so can dangerously reduce control-lability, resulting in an accident.! Wheel replacementWhen rep

11-58Maintenance and serviceWindshield washer fluidNever use engine coolant as washer fluid be-cause it could cause paint damage.If you spray washer f

11-59Maintenance and service– CONTINUED –Remove the washer tank filler cap, then check the fluidlevel indicated by the level gauge (attached to the in

11-60Maintenance and serviceReplacement of wiper bladesGrease, wax, insects, or other materials on the wind-shield or the wiper blade results in jerky

1-25Seat, seatbelt and SRS airbags– CONTINUED –retracted properly to avoid catching the belt webbingin the door.! Rear seatbelts (except rear center s

11-61Maintenance and service– CONTINUED –A) Stopper3. Remove the wiper blade assembly by holding itspivot area and pushing it in the direction shown b

11-62Maintenance and serviceA) Metal spines2. If the new blade rubber is not provided with twometal spines, remove the metal spines from the oldblade

11-63Maintenance and service– CONTINUED –A) Stopper4. Be sure to position the claws at the end of the metalsupport between the stoppers on the rubber

11-64Maintenance and service3. Pull the wiper blade assembly toward you to re-move it from the wiper arm.! Rear window wiper blade rubber1. Pull out t

11-65Maintenance and service– CONTINUED –2. Pull the blade rubber assembly out of the plasticsupport.A) Metal spines3. If the new blade rubber is not

11-66Maintenance and service4. Align the claws of the plastic support with thegrooves in the blade rubber assembly, then slide theblade rubber assembl

11-67Maintenance and service– CONTINUED –Battery" Before beginning work on or near any bat-tery, be sure to extinguish all cigarettes, match-es,

11-68Maintenance and serviceFusesNever replace a fuse with one having a higherrating or with material other than a fuse be-cause serious damage or a f

11-69Maintenance and service– CONTINUED –The other one is housed in the engine compartment. The spare fuses are stored in the main fuse box coverin t

11-70Maintenance and serviceThe fuse puller is stored in the main fuse box in the en-gine compartment.A) GoodB) BlownIf any lights, accessories or oth

1-26Seat, seatbelt and SRS airbags" Unfastening the seatbeltPush the button on the buckle.Before closing the door, make sure that the belts arere

11-71Maintenance and service– CONTINUED –each fuse.4. Pull out the fuse with the fuse puller.5. Inspect the fuse. If it has blown, replace it with asp

11-72Maintenance and serviceInstallation of accessoriesAlways consult your SUBARU dealer before installingfog lights or any other electrical equipment

11-73Maintenance and service– CONTINUED –Replacing bulbs810945321671817 16 151713 1411 1218UBB208BB

11-74Maintenance and service! HeadlightHalogen headlight bulbs become very hot whilein use. If you touch the bulb surface with barehands or greasy glo

11-75Maintenance and service– CONTINUED –" It may be difficult to replace the bulbs. Haveyour SUBARU dealer replace the bulbs if neces-sary.! Low

11-76Maintenance and service! High beam light bulbs1. Disconnect the electrical connector from the bulb.2. Remove the bulb from the headlight assembly

11-77Maintenance and service– CONTINUED –A) Rear turn signal lightB) Backup lightC) Brake/tail and rear side marker light2. Remove the bulb holder fro

11-78Maintenance and service2. Wrap tape around a flat-head screwdriver, then in-sert the screwdriver into the gap A between the sidecover and rear co

11-79Maintenance and service– CONTINUED –A) Brake/tail lightB) Rear turn signal lightC) Rear side marker light4. Remove the bulb holder from the rear

11-80Maintenance and service2. Turn the bulb socket counterclockwise and removeit.3. Pull the bulb out of the bulb socket and replace itwith a new one

1-27Seat, seatbelt and SRS airbags– CONTINUED –Fastening the seatbelt with the webbing twistedcan increase the risk or severity of injury in anacciden

11-81Maintenance and service– CONTINUED –! Station wagon01. Remove the mounting screws using a Phillipsscrewdriver.2. Remove the lens.3. Pull the bulb

11-82Maintenance and service! Dome light1. Remove the lens by prying the edge of the lens witha flat-head screwdriver.2. Turn the bulb until the flat

11-83Maintenance and service– CONTINUED –! Map light01. Remove the lens by prying the edge of the lens witha flat-head screwdriver.2. Turn the bulb un

11-84Maintenance and service! Door step light1. Remove the lens by prying the edge of the lens witha flat-head screwdriver.2. Pull the bulb out of the

11-85Maintenance and service– CONTINUED –! Cargo area light1. Remove the cargo area light assembly by pryingthe edge of the light with a flat-head scr

11-86Maintenance and service! Trunk light1. Remove the cover by pulling it out.2. Pull the bulb out of the socket. Install a new bulb.3. Reinstall the

12-112SpecificationsSpecifications ... 12-2Dimensions ...

12-2SpecificationsSpecificationsSpecificationsThese specifications are subject to change without notice.! Dimensionsin (mm)Item Legacy OUTBACKSedan S

12-3Specifications– CONTINUED –! Engine! Electrical systemEngine model EJ253(2.5-liter, SOHC, non-turbo)EJ255 (2.5-liter, DOHC, turbo)EZ30D(3.0-liter,

12-4Specifications! CapacitiesFuel tank 16.9 US gal (64 liters, 14.1 Imp gal)Engine oil 2.5-liter models 4.2 US qt (4.0 liters, 3.5 Imp qt)3.0-liter m

1-28Seat, seatbelt and SRS airbagsRear center seatbelt is stowed in the recess of the ceil-ing.1. Remove the connector (tongue) plate from theholder l

12-5Specifications– CONTINUED –! Tires! Wheel alignmentTire size P205/55R16 89H 215/45ZR17 P225/60R16 97H P225/55R17 95VWheel size 16 x 6.5JJ 17 x 7JJ

12-6SpecificationsFuses and circuits! Fuse panel located in the passenger compartment27 28 29 30 31 32 3320 21 22 23 24 25 2613 14 15 16 17 18 196 7 8

12-7Specifications– CONTINUED –11 7.5 " Turn signal unit" Clock12 15 " Automatic transmis-sion unit" SRS airbag system (Sub)"

12-8Specifications! Fuse panel located in the engine com-partmentA) FWD socket (AT vehicles – except Turbo models and 3.0-liter models)B) Main fuse32

12-9Specifications– CONTINUED –Fuse panel Fuse rating Circuit1 30 " ABS unit" Vehicle dynamics con-trol unit2 25 " Main fan3 25 "

12-10SpecificationsBulb chartDescription Wattage Bulb No.Headlight Low beam 12V-55W H7High beam 12V-60W 9005 (HB3)Fog lightExcept OUTBACK 12V-55W H3OU

12-11Specifications– CONTINUED –Vehicle identification12865437UBC200BB1) Emission control label2) Vehicle identification number3) Certification and ba

13-113Consumer information and Reporting safety defectsTire information ... 13-2Tire labeling ...

13-2Consumer information and Reporting safety defectsConsumer inf ormation and R eporting safety defectsFor U.S.A.The following information has been

3– CONTINUED –Chapter 13: Consumer information and Reportingsafety defectsThis chapter informs you about Tire information, Uni-form tire quality gradi

1-29Seat, seatbelt and SRS airbags– CONTINUED –3. After confirming that the webbing is not twisted, in-sert the connector (tongue) attached at the web

13-3Consumer information and Reporting safety defects– CONTINUED –First, the number designation is its load index.Second, the letter designation indic

13-4Consumer information and Reporting safety defects(1) Manufacturer’s Identification Mark(2) Tire Size(3) Tire Type Code(4) Date of ManufactureThe f

13-5Consumer information and Reporting safety defects– CONTINUED –" Uniform Tire Quality Grading (UTQG)For details, refer to “Uniform tire qualit

13-6Consumer information and Reporting safety defects! Recommended tire inflation pressure! Recommended cold tire inflation pressureRecommended cold t

13-7Consumer information and Reporting safety defects– CONTINUED –! Vehicle placardThe vehicle placard is affixed to the driver’s sideB-pillar.Example

13-8Consumer information and Reporting safety defectshicle control could lead to an accident.! Measuring and adjusting air pressure to achieve proper

13-9Consumer information and Reporting safety defects– CONTINUED –" Maximum loaded vehicle weightThe sum of curb weight, accessory weight, vehi-c

13-10Consumer information and Reporting safety defectsleft hand side of the vehicle. (Each tire must bekept on its original side of the vehicle.) Repl

13-11Consumer information and Reporting safety defects– CONTINUED –Vehicle capacity weight of the vehicle is 800 lbs(363 kg), which is indicated on th

13-12Consumer information and Reporting safety defectsnumber of occupants to two), the calculationsare as follows:1. Calculate the total weight.2. Cal

1-30Seat, seatbelt and SRS airbags5. Insert the center seatbelt tongue plate in the centerseatbelt buckle marked “CENTER” on the left handside until i

13-13Consumer information and Reporting safety defects– CONTINUED –the trailer tongue (i.e. Tongue load = 176 lbs (80kg)).1. Calculate the total weigh

13-14Consumer information and Reporting safety defects2. Calculate the available load capacity.3. The total weight now exceeds the capacityweight by 2

13-15Consumer information and Reporting safety defects– CONTINUED –! Adverse safety consequences of over-loading on handling and stopping and on tires

13-16Consumer information and Reporting safety defectsUniform tire quality grading stan-dardsThis information indicates the relative perfor-mance of p

13-17Consumer information and Reporting safety defects– CONTINUED –tests, and does not include acceleration,cornering, hydroplaning, or peak tractionc

13-18Consumer information and Reporting safety defectsReporting safety defects (USA)If you believe that your vehicle has a defectwhich could cause a c

14-114Index

14-2IndexAABS (Anti-lock Brake System) ... 7-38Warning light ... 3-28, 7-39Accessories .

14-3IndexBulbChart ... 12-10Replacing ... 11-

14-4IndexCup holderFront passenger’s ... 6-12Rear passenger’s ... 6-13D

1-31Seat, seatbelt and SRS airbags– CONTINUED –" Unfastening the seatbeltPush the release button of the center seatbelt buckle(on the left hand s

14-5IndexFog light ... 11-76Seatbelt pretensioners ... 1-33Seats ...

14-6IndexKKeyKeyless entry system ... 2-12Number ... 2-3Rem

14-7IndexOil pressure warning light ... 3-26Outside mirrors ... 3-61Outs

14-8IndexLicense plate light ... 11-80Map light ... 11-83Parki

14-9IndexTilt steering wheel ... 3-63TireChains ...

14-10IndexBrake system ... 3-29Charge ... 3-26CH

109876543111213HSF028AA

GAS STATION REFERENCEFuel:! 2.5-liter non-turbo modelsUse only unleaded gasoline with an octane rating of87 AKI or higher.! 2.5-liter turbo models and

1-32Seat, seatbelt and SRS airbagsslot in the connector (buckle) on the right hand sideand push it in, and the connector (tongue) plate willdisconnect

1-33Seat, seatbelt and SRS airbags– CONTINUED –! Seatbelt maintenanceTo clean the seatbelts, use a mild soap and lukewarmwater. Never bleach or dye th

1-34Seat, seatbelt and SRS airbagsing noise will be heard and a small amount of smokewill be released. These occurrences are normal andnot harmful. Th

1-35Seat, seatbelt and SRS airbags– CONTINUED –your SUBARU dealer.! System monitorsSRS airbag system warning lightA diagnostic system continually moni

1-36Seat, seatbelt and SRS airbags" Front passenger’s frontal airbag ON and OFF indi-cator" All related wiringIf the warning light exhibits

1-37Seat, seatbelt and SRS airbags– CONTINUED –those areas or near the front seatbelt retrac-tors, we recommend that you have an autho-rized SUBARU de

1-38Seat, seatbelt and SRS airbagsChild restraint systemsInfants and small children should always be placed inan infant or child restraint system in t

4ual. This symbol means “Do not”, “Do not do this”, or“Do not let this happen”, depending upon the context.Vehicle symbolsThere are some of the symbol

1-39Seat, seatbelt and SRS airbags– CONTINUED –Never let a passenger hold a child on his or herlap while the vehicle is moving. The passengercannot pr

1-40Seat, seatbelt and SRS airbags! Where to place a child restraint systemThe following are SUBARU’s recommendations onwhere to place a child restrai

1-41Seat, seatbelt and SRS airbags– CONTINUED –dren are safer when properly restrained in therear seating positions than in the front seatingpositions

1-42Seat, seatbelt and SRS airbagssystem. Also it is important for you to make sure thatthe child restraint system is compatible with the vehi-cle in

1-43Seat, seatbelt and SRS airbags– CONTINUED –hear a click.4. Take up the slack in the lap belt.5. Pull out the seatbelt fully from the retractor toc

1-44Seat, seatbelt and SRS airbags8. To remove the child restraint system, press the re-lease button on the seatbelt buckle and allow the beltto retra

1-45Seat, seatbelt and SRS airbags– CONTINUED –4. Take up the slack in the lap belt.5. Pull out the seatbelt fully from the retractor tochange the ret

1-46Seat, seatbelt and SRS airbagsSedan Station wagon8. If the child restraint system requires a top tether,latch the hook onto the top tether anchor

1-47Seat, seatbelt and SRS airbags– CONTINUED –9. To remove the child restraint system, press the re-lease button on the seatbelt buckle and allow the

1-48Seat, seatbelt and SRS airbagsthe event of an accident may be increased.1. Place the booster seat in the rear seating positionand sit the child on

5– CONTINUED –Child restraint lower anchoragesChild restraint top tether anchoragesHornWindshield wiper deicerWiper intermittentWindshield wiper and w

1-49Seat, seatbelt and SRS airbags– CONTINUED –effective in preventing or reducing injury." Place the lap belt as low as possible on thechild’s h

1-50Seat, seatbelt and SRS airbagsYour vehicle is equipped with four lower anchorages(bars) and three upper anchorages (tether anchorag-es) for accomm

1-51Seat, seatbelt and SRS airbags– CONTINUED –SedanStation wagonThe tether anchorages (upper anchorages) are pro-vided for all the seating positions

1-52Seat, seatbelt and SRS airbagsSedan Station wagonYou will find marks “ ” at the bottom of the rearseat seatbacks. These marks indicate the positio

1-53Seat, seatbelt and SRS airbags– CONTINUED –danger of your child suffering personal injury inthe event of an accident may be increased.01. Sedan: M

1-54Seat, seatbelt and SRS airbags2. While following the instructions supplied by thechild restraint system manufacturer, connect the lowerhooks onto

1-55Seat, seatbelt and SRS airbags– CONTINUED –5. Before seating a child in the child restraint system,try to move seat back and forth and left and ri

1-56Seat, seatbelt and SRS airbags" Station wagonThree tether anchorages, i.e., ones for the right, cen-ter and left positions, are already insta

1-57Seat, seatbelt and SRS airbags– CONTINUED –2. Open the cover flaps to use the anchorages.3. Fasten the top tether hook of the child restraint sys-

1-58Seat, seatbelt and SRS airbags" Station wagon01. Remove the head restraint at the seating positionwhere the child restraint system has been i

6Safety precautions when driving! Seatbelt and SRS airbag" All persons in the vehicle should fasten theirseatbelts BEFORE the vehicle starts to m

1-59Seat, seatbelt and SRS airbags– CONTINUED –3. Fasten the top tether hook of the child restraint sys-tem to the appropriate upper anchorage.4. Tigh

1-60Seat, seatbelt and SRS airbagsThese SRS airbags are designed only as a supple-ment to the primary protection provided by theseatbelt.The system al

1-61Seat, seatbelt and SRS airbags– CONTINUED –SRS airbag cover or between you and the SRSairbag. If the SRS airbag deploys, those objectscould interf

1-62Seat, seatbelt and SRS airbagsthe front passenger’s seat, or never hold a childon your lap or in your arms. The SRS airbag de-ploys with considera

1-63Seat, seatbelt and SRS airbags– CONTINUED –! ComponentsSedan 1234561819232281113201720121079212020141615UB1219BB1) Airbag control module (includin

1-64Seat, seatbelt and SRS airbagsStation wagon 1234520202197101220172013618192322811141516UB1218BB1) Airbag control module (including im-pact sensors

1-65Seat, seatbelt and SRS airbags– CONTINUED –! Subaru advanced frontal airbag sys-temYour vehicle is equipped with a Subaru advancedfrontal airbag s

1-66Seat, seatbelt and SRS airbagsCLOSE TO THE SRS AIRBAG.Never allow a child to stand up, or to kneel onthe front passenger’s seat. The SRS airbag de

1-67Seat, seatbelt and SRS airbags– CONTINUED –The SRS airbag deploys with considerablespeed and force. Occupants who are out ofproper position when t

1-68Seat, seatbelt and SRS airbagsDo not attach accessories to the windshield, orfit an extra-wide mirror over the rear view mir-ror. If the SRS airba